Key takeaways
·Office lighting has to hit 500 lux at UGR ≤ 19 and uniformity ≥ 0.6 while keeping connected load low — the three requirements are now compatible, but only if all three are written into the specification.
·Annual energy at 2,000 hours shows the gap clearly: a 1,500 mm linear at 40 W / 6,000 lm / UGR 16 uses 80 kWh, a 600×600 panel at 32 W / 4,300 lm / UGR 19 uses 64 kWh, a 12 W desk lamp uses 24 kWh.
·Linear systems are the efficient default for open plan; panels belong in cellular offices and meeting rooms where the ceiling grid is already fixed.
·Daylight harvesting pays back only when the control strategy is zoned to the daylight aperture, not applied as one sensor per floor.
The targets, stated precisely
EN 12464-1 is the reference standard across Europe and is widely copied elsewhere. For offices it sets:
Task area | Maintained illuminance | UGR | Uniformity Uo | CRI |
Writing, typing, reading | 500 lux | 19 | 0.60 | 80 |
CAD workstation | 500 lux | 19 | 0.60 | 80 |
Conference room | 500 lux | 19 | 0.60 | 80 |
Archive / filing | 300 lux | 25 | 0.40 | 80 |
Reception | 300 lux | 22 | 0.40 | 80 |
Corridor / circulation | 100 lux | 28 | 0.40 | 80 |
Note "maintained": the design must still deliver 500 lux at the maintenance interval, allowing for 15–20 % light loss from dirt and depreciation. A layout calculated at exactly 500 lux on day one will be non-compliant in three years.
Linear systems: the efficient default
Linear luminaires are the standard for open-plan offices because they align with desk rows and can be optically controlled.
Efficacy in context. 140–170 lm/W at the luminaire is achievable at 4,000 K, CRI 80. A 1,500 mm, 40 W unit at 150 lm/W delivers 6,000 lm — enough for roughly 12 m² at 500 lux with an optical efficiency of 0.7.
Glare control. A louvre optic at UGR ≤ 16 costs 10–15 % of output but is the correct choice for rows parallel to and above monitor banks. Opal diffusers at UGR 19–22 are acceptable only where fixtures run perpendicular to sightlines.
Suspension height. Suspended 300–500 mm below the ceiling, with an up/down ratio around 70/30, produces a brighter ceiling and a more comfortable room. A 100 % downlight distribution creates a cave effect that occupants complain about without being able to name it.
Controls. DALI-2 with a D4i driver provides dimming, occupancy, daylight harvesting and energy reporting over the same pair of wires. For a 2026 fit-out this is the default, not the upgrade.
Panel lights: where they belong and where they do not
Panels are cost-effective, plenum-friendly and quick to install. They are also the wrong product in a room with monitors facing the ceiling.
Correct use: cellular offices, meeting rooms, corridors, back-of-house, and retrofit into existing 600×600 grid ceilings where a linear system would require new suspension.
Incorrect use: deep open-plan floors with rows of desks — a flat 600×600 panel at UGR 19 still produces veiling reflections at the typical 2.7 m ceiling height.
The specification that matters. 130–150 lm/W, UGR ≤ 19, flicker < 5 % at all dimming levels, CRI 80 with R9 > 0, and an isolated driver. Insist on the flicker figure measured at 10 % dimming — this is where budget drivers are exposed in video-call-heavy offices.
Daylight harvesting: the control strategy that pays
Of all control strategies, daylight dimming delivers the largest and most reliable saving in offices — typically 25–35 % of lighting energy in a perimeter zone, with a payback of two to four years.
Sensor placement. A closed-loop sensor inside the luminaire is simple but can be fooled by the fixture's own output. An open-loop sensor aimed at the window measures daylight directly and is more accurate, at the cost of a separate installation.
Dimming range. The driver must dim smoothly to 1–5 % without flicker or visible stepping; a driver that cuts out below 10 % will produce a visible pop at dusk.
Zoning. Group fixtures in rows parallel to the facade, typically 3–4 m deep per zone. Zoning by individual fixture produces visible brightness differences across a ceiling.
Commissioning. Set target illuminance at 500 lux, not at maximum output, and record the setpoints. Uncommissioned systems run at 100 % and deliver no savings at all — the single most common failure in "sensor-equipped" buildings.
Desk lamps: the hybrid-work correction
With hybrid working, the task light has returned — not as decoration but as a way to reduce ambient levels in partially occupied floors.
Illuminance and uniformity. A good desk lamp delivers 500–1,000 lux on the task area with uniformity better than 0.6 across an A3 sheet. Look for a stated illuminance at a stated distance (for example 1,000 lux at 400 mm).
Flicker. Below 1 % modulation, ideally with a DC driver. Cheap desk lamps flicker at 30–50 %, which causes measurable eye strain over a working day.
Colour quality. CRI 90–95 with R9 above 50 matters for anyone reviewing print, textiles or packaging. 4,000 K is a practical default; adjustable 2,700–5,000 K suits shared spaces.
Asymmetric optics. A lamp that throws light forward onto the desk, not into the user's eyes, is the difference between a professional task light and a bright object on a desk.
Product | Typical spec | Annual energy (2,000 h) | Best application |
Linear, 1,500 mm | 40 W, 6,000 lm, UGR 16 | 80 kWh | Open plan, drawing office |
Panel, 600×600 | 32 W, 4,300 lm, UGR 19 | 64 kWh | Cellular office, meeting room |
Desk lamp | 12 W, 1,000 lux @ 400 mm | 24 kWh | Hybrid workstation |
Downlight, 150 mm | 25 W, 3,000 lm | 50 kWh | Reception, breakout |
Calculating LENI before the fit-out
EN 15193-1 expresses lighting energy as LENI — kWh per m² per year. A well-controlled LED office reaches 8–12 kWh/m²/yr; a poorly controlled one with the same fixtures reaches 25–30. The difference is entirely occupancy sensing, daylight dimming and commissioning.
The quick estimate: connected load density (W/m²) × annual operating hours ÷ 1,000, then apply the control factor. A 6 W/m² LED installation with occupancy and daylight control at 2,200 hours yields approximately 9 kWh/m²/yr. The same installation without controls yields 13.2.
A specification checklist for the fit-out team
1.Illuminance and UGR calculated room by room, with the maintenance factor stated.
2.Flicker measurement at 10 % dimming for every dimmable type.
3.Driver brand and model named in the schedule, with the warranty terms for the driver separately stated.
4.Control philosophy drawn as a zoning plan, with sensor types and setpoints.
5.Commissioning report with measured illuminance per zone.
LFL Lighting supplies office linear systems, panels and task lights with UGR and flicker reports included, and can produce a DIALux evo calculation and a control zoning plan from your floor plan. Send the drawing and the target LENI — we will return a compliant scheme.
Contact: shally@longingforlight.com | Request DIALux calculation and control zoning plan
Frequently asked questions
How many lux does an office need?
500 lux maintained on the task area for writing, typing, reading and CAD work. Archives and filing need 300 lux, reception 300 lux, and corridors or circulation 100 lux.
What is LENI and what counts as a good value?
LENI is the Lighting Energy Numeric Indicator in kWh per square metre per year, covering installed load, daylight availability, occupancy and control strategy. It is the number to calculate before the fit-out, because controls change it more than fixture efficacy does.
Should an open-plan office use linear lights or panels?
Linear. A 1,500 mm linear system reaches UGR 16 at 40 W for 6,000 lm and puts light where the desks are. Panels suit cellular offices and meeting rooms where the 600×600 ceiling grid already exists.
Related reading: Comprehensive Commercial Indoor Lighting Analysis · Commercial & Hospitality LED Lighting Supplier Catalog · 2026 High-Efficiency LED Lighting Systems Guide.