Key takeaways
·Emergency lighting is specified by failure mode and by EN 1838 illuminance, not by lumen output: 1 lux on escape route centrelines, 10 lux anti-panic in open areas over 60 m², 15 lux on high-risk task areas.
·Three hours is the standard autonomy for occupied buildings; one hour is accepted only where the building is evacuated immediately on supply failure.
·Ask for the end-of-life battery threshold — 70 % of rated capacity is the usual pass mark — rather than nominal Ah.
·Housing construction decides tri-proof survival: silicone gasket, IP67 external driver and M20 gland with strain relief, tested against the site's actual cleaning chemicals.
Tri-proof lights: passing an audit, not just an IP test
A tri-proof fixture in a food plant, a bottling line or a cold store is inspected by people carrying a checklist. The items on that checklist:
Ingress and impact. IP66 minimum for wash-down; IP69K where high-pressure, high-temperature jets are used (typically 80–100 bar at 80 °C). IK08 minimum, IK10 for areas with trolley traffic. Both must be certified, with the report available on request.
Housing material. Polycarbonate with UV stabiliser for general industry; glass-filled polyester or stainless-steel-clad for chemical plants. ABS is acceptable indoors but embrittles under UV.
Seal integrity after re-lamping. This is the test most fixtures fail. A silicone gasket compressed by stainless clips survives 50 opening cycles; a foamed tape gasket compressed by plastic tabs does not. Ask how many cycles the seal is rated for.
Chemical compatibility. In dairy and beverage plants, cleaning agents include sodium hydroxide and peracetic acid. A polycarbonate diffuser resists both; a polystyrene one crazes within a year. Get the compatibility list in writing.
Light quality for inspection tasks. Where staff inspect product, CRI 90 and a diffuse, shadow-free distribution matter more than efficacy. A 150 lm/W fixture with a harsh linear source creates reflections that hide defects.
Application | Rating requirement | Wattage | CCT / CRI | Notes |
Food processing | IP66–IP69K, IK08 | 20–60 W | 4000–5000 K, CRI 90 | Chemical list required |
Cold store (−40 °C) | IP66, IK08 | 30–50 W | 4000 K, CRI 80 | Silicone cable, low-temp driver |
Chemical plant | IP66, IK10 | 20–60 W | 5000 K, CRI 80 | Stainless or GRP housing |
Warehouse aisle | IP65, IK08 | 40–80 W | 4000–5700 K, CRI 70 | Linkable, 1-10 V |
Car wash | IP69K, IK08 | 30–50 W | 6500 K, CRI 80 | Corrosion-resistant clips |
Portable work lights: the specification buyers forget to write
Site work lights are bought in volume and specified in a single line, which is why they fail. The parameters that matter in use:
Cable and plug. A 5 m HO5RN-F rubber cable with a moulded IP44 plug survives site handling; PVC cable with a wired plug does not. For 110 V sites (UK construction), the transformer must be integral or matched, not improvised.
Body and stand. Die-cast aluminium or engineering polymer with a steel frame; a folding stand rated to 1.5× the fixture weight; a magnetic base (30–50 kg pull) for steel structures. The joint is what breaks, not the LED.
Daisy-chain capability. Site users run 3–5 units from one feed. Confirm the socket outlet is rated for the total load and that the pass-through is IP44 when mated.
Light quality. For inspection and painting, CRI 90 and a broad beam (100–120°) reduce eye strain and rework. For general task lighting, 5000 K at 100 lm/W is the practical norm.
Work light type | Power | Output | IP | Cable | Best use |
Compact handheld | 20–30 W | 2,000–3,000 lm | IP54–IP65 | 3–5 m | Maintenance, cabinets |
Floor stand | 50–100 W | 5,000–10,000 lm | IP65 | 5 m | Site task lighting |
Magnetic bar | 30–50 W | 3,000–5,000 lm | IP65 | 5 m | Machine beds, steel frames |
Rechargeable | 10–30 W | 1,000–3,000 lm | IP65 | USB-C | Confined space, night work |
Canopy fixtures: petrol stations, loading bays and under-deck lighting
Canopy lighting has two distinct requirements that are often conflated.
Forecourt canopies need high illuminance (typically 300–500 lux at the pump island), excellent vertical illuminance for camera identification, and minimal spill upward. The correct product is a recessed or surface canopy luminaire with a symmetric or square distribution, 60–150 W, IP65, with a flat glass lens that cleans easily. For hazardous-area installations, the fixture must carry the appropriate Ex rating for the zone classification — do not accept a standard IP65 unit for a classified area.
Loading bay and under-deck canopies need robustness and control: IP65, IK08, motion sensing with 3-step dimming, and a mounting height of 4–6 m. A 60–100 W low-bay fixture with a 90–120° beam covers a 5×5 m bay.
Canopy type | Wattage | Beam | IP / IK | Control |
Forecourt, recessed | 60–120 W | Symmetric 90–120° | IP65 / IK08 | Central photocell |
Forecourt, surface | 80–150 W | Square distribution | IP65 / IK08 | DALI / 0-10 V |
Loading bay | 40–100 W | 90–120° | IP65 / IK08 | PIR 3-step |
Under-deck | 20–50 W | 120° | IP65 / IK08 | On/off |
Emergency lighting: autonomy, mode and testing
Emergency units are a compliance product, and the requirements are specific:
·Autonomy: 3 hours is the standard for most occupied buildings; 1 hour is accepted in some jurisdictions only where the building is evacuated immediately.
·Illuminance: EN 1838 asks for 1 lux on escape route centrelines, 10 lux anti-panic in open areas over 60 m², and 15 lux on high-risk task areas.
·Modes: maintained (on all the time, used as normal lighting too) versus non-maintained (energises only on supply failure). Specify per location, not per project.
·Self-test: DALI or addressable self-test units report monthly and annual function tests automatically; manual test logs are increasingly rejected by auditors.
·Battery: LiFePO4 now dominates over NiCd for cycle life and temperature tolerance. Ask for the end-of-life capacity threshold — 70 % of rated is typical.
Type | Output | Autonomy | Mode | Testing |
Emergency bulkhead | 200–400 lm | 3 h | Maintained / non-maintained | Manual or self-test |
Emergency downlight | 150–300 lm | 3 h | Non-maintained | Self-test |
Exit sign | 100–300 lm | 3 h | Maintained | Self-test |
Emergency linear module | 300–800 lm | 3 h | Maintained | DALI self-test |
Documentation that closes an audit
For every industrial safety fixture, keep on file: the IP and IK test reports, the LM-79 report, the emergency autonomy test certificate, the chemical compatibility list (where relevant), and the installation instructions in the local language. Sites that fail safety audits almost always fail on paperwork rather than product.
LFL Lighting manufactures tri-proof, work, canopy and emergency luminaires with certification packages prepared for EU, Middle East and Southeast Asian inspections. Send us your site classification and cleaning regime — we will specify the housing material and rating that survive it.
Contact: shally@longingforlight.com | Request certification package and IP69K report
Frequently asked questions
What illuminance does EN 1838 require on an escape route?
1 lux along the centreline of the escape route, 10 lux anti-panic in open areas larger than 60 m², and 15 lux on high-risk task areas such as plant rooms and control points.
How long must emergency lighting stay on after a power failure?
Three hours for most occupied buildings. One hour is accepted in some jurisdictions only where the premises are evacuated immediately when the supply fails.
What IP rating do I need for a tri-proof light in a car wash or food plant?
IP69K with IK08 for high-pressure hot-water wash-down, plus a chemical-resistance list for the detergents used on site. IP65 is only rated for water jets at low pressure.
Related reading: Industrial & Commercial LED Lighting Directory · Portable & Emergency LED Work Lighting Selection Matrix · Next-Generation Solar Outdoor Lighting Systems.