loading

LFL Lighting - Full Process LED Lighting Solutions Provider Since 2013.

Municipal & Outdoor LED Street Lighting Benchmark: Comparing All-In-One Solar Street Lights, Wall Packs and Stadium Lighting1

Key takeaways

·All-in-one solar street light sizing is arithmetic, not branding: residential road 30–50 W LED on a 60–90 W panel and 12.8 V / 30–40 Ah battery at 5–6 m; main road 100–150 W on 200–300 W and 25.6 V / 60–100 Ah at 9–12 m.

·Wall packs are a light-trespass product: full cut-off optics at 130–155 lm/W are what councils and dark-sky policies actually require.

·Stadium lighting is judged on uniformity and flicker before output: broadcast installations need TLCI above 90 and flicker below 1 %.

·A tender review should test the quotation against the load calculation, not against the competitor's price.


All-in-one solar street lights: the four numbers in the datasheet


The all-in-one format integrates panel, LiFePO4 battery, controller and LED in a single head. It is the fastest-growing outdoor category because installation cost collapses, but it is also where optimistic specifications are most common.

1. Usable battery capacity, not nominal. A "30 Ah" pack using 3.2 V cells is 96 Wh nominal; usable capacity at 90 % depth of discharge is ~86 Wh, and at end of life (80 % state of health) about 69 Wh. Design the system on the last number.

2. Autonomy days. Ask for autonomy at the specified lighting profile. A 60 W fixture running 10 hours at 100 % then 70 % requires far more storage than the "12 hours" headline suggests. Three consecutive cloudy days is the normal standard for municipal work.

3. Panel-to-load ratio. A practical minimum is 1.5–2.0 W of panel per watt of LED load for temperate latitudes, higher in northern or monsoon climates. A 100 W head with an 80 W panel will not recover in winter.

4. Luminous flux stability over five years. LEDs in a sealed head at 60 °C lose output faster than the datasheet suggests; a 5 % annual depreciation assumption is safe for planning.


All-in-one class

LED power

Delivered flux

Panel

Battery (LiFePO4)

Mounting height

Residential road

30–50 W

4,500–7,500 lm

60–90 W

12.8 V / 30–40 Ah

5–6 m

Collector road

60–90 W

9,000–13,500 lm

120–180 W

25.6 V / 30–50 Ah

7–8 m

Main road

100–150 W

15,000–22,000 lm

200–300 W

25.6 V / 60–100 Ah

9–12 m


A design calculation you can check yourself. Load energy = LED watts × hours × duty factor. For a 60 W head at 10 h with a 0.8 average dimming factor: 60 × 10 × 0.8 = 480 Wh per night. With 3 autonomy days and 80 % usable DoD: 480 × 3 ÷ 0.8 = 1,800 Wh of nominal storage — that is roughly a 25.6 V / 70 Ah pack. If a supplier quotes 40 Ah for that duty, the numbers do not close.


Also verify the mounting and wind load. An integrated head is a sail; the bracket and pole interface should be rated for the local wind zone, and the panel tilt should be adjustable for latitude.


Wall packs: cut-off optics and the dark-sky question


Wall packs light the perimeter of buildings, car parks and service yards. Two specifications dominate:


Cut-off classification. For projects in jurisdictions following dark-sky guidance (many EU and North American municipalities), specify full cut-off — no light emitted above the horizontal. A "wall pack" with a sag-lens refractor sends 10–20 % of its output into the sky, which fails the review and wastes energy.


Photocell and sensor behaviour. A quality photocell has a 30–60 second delay and a hysteresis band of 10–20 lux; a cheap one switches on at dusk and off at dawn, then chatters under passing headlights. Where the client wants security response, combine a photocell with a PIR that raises output from 30 % to 100 % — not a fixture that runs at 100 % all night.


Wall pack type

Wattage

Efficacy

IP / IK

Control

Standard forward throw

20–60 W

120–150 lm/W

IP65 / IK08

Photocell

Full cut-off

30–80 W

130–155 lm/W

IP65 / IK08

Photocell + PIR

Adjustable head

40–100 W

120–145 lm/W

IP66 / IK08

0-10 V

Emergency battery

20–40 W

110–130 lm/W

IP65 / IK08

Self-test


Stadium and sports lighting: uniformity, flicker, and aiming


Sports lighting is the most technically demanding outdoor application, and the one where cheap fixtures are most quickly exposed.


Uniformity and glare. For amateur football or tennis, Uo ≥ 0.5 and GR ≤ 50; for broadcast-standard venues, Uo ≥ 0.7 and GR ≤ 30. These are achieved with asymmetric multi-module floodlights (300–1,500 W), precise aiming and a lighting design file — never by adding fixtures.


Flicker-free operation. Any venue with super-slow-motion cameras needs flicker below 1 % and a high-speed camera-friendly driver. A 4,000 Hz+ driver with a stated ripple of < 3 % is the benchmark; consumer-grade drivers will band on replay even though they look fine to the eye.


Maintenance access. Specify a driver that can be replaced at the fixture, front-access, with the floodlight in place. A stadium with 40 fixtures at 30 m does not want to lower masts for a driver swap.


Level

Fixture power

Efficacy

CRI / TLCI

Flicker

Pole height

Training / amateur

200–400 W

140–160 lm/W

Ra 80

< 8 %

12–18 m

Club competition

400–800 W

140–160 lm/W

Ra 80–90

< 5 %

18–25 m

Broadcast

800–1,500 W

130–150 lm/W

TLCI > 90

< 1 %

25–45 m


Tender review checklist

1.LM-79 report for the exact model, plus IES file for the layout calculation.

2.IP66 and IK08 certificates from an accredited lab, with the report number.

3.Surge protection rating stated in kV and kA (10 kV/10 kA minimum for exposed sites).

4.For solar: autonomy calculation at the client's latitude, with the battery chemistry and DoD stated.

5.Warranty terms including the driver and the battery, with a defined end-of-life capacity threshold.


LFL Lighting supplies municipal-grade street lights, wall packs and sports floodlights with full photometric and test documentation, and can produce a DIALux layout from your road or site drawing. Tell us the road class, pole height and spacing, and we will return a compliant design.


Contact: shally@longingforlight.com | Request DIALux layout and tender documentation


Frequently asked questions


How do I check whether a solar street light quotation is realistic?


Multiply LED watts by nightly operating hours, divide by depth of discharge, then add autonomy days. A 60 W fixture running 10 hours at 0.8 efficiency needs 480 Wh per night; three days of autonomy at 90 % DoD implies roughly 1.6 kWh, which is about 70 Ah at 25.6 V. A quote offering 40 Ah cannot deliver it.


What is full cut-off and why do councils require it?


Full cut-off means no light is emitted at or above the horizontal, so nothing spills upward into the sky or into neighbouring windows. It is the standard response to dark-sky policy and light-trespass complaints.


What flicker level is acceptable for broadcast stadium lighting?


Below 1 % modulation, with TLCI above 90. Above that, slow-motion replay shows banding and the venue cannot host televised fixtures.


Related reading: Next-Generation Solar Outdoor Lighting Systems · Industrial & Commercial LED Lighting Directory · 2026 High-Efficiency LED Lighting Systems Guide.


prev
Architectural & Decorative LED Luminaire Engineering: Design Applications for Wall Washers, Strip Lights and Hologram Displays1
Industrial Safety & Emergency LED Lighting Specs: Complete Manual for Tri-Proof Lights, Work Lights and Canopy Fixtures1
next
recommended for you
Get in touch with us
Contact Us
Tel/Fax: +86 - 592 - 532 7905
Skype: shally558826
QQ: 25 9661 5780
Wechat / Whatsapp / MP: +86 131 5923 0163
Add: 2F NO.507 West JinyuanRoad, Jimmei District  Xiamen , Fujian, China
Copyright © 2026 LFL | Sitemap | Privacy Policy
Contact us
phone
whatsapp
Contact customer service
Contact us
phone
whatsapp
cancel
Customer service