Key takeaways
·Hospitality lighting is specified in four layers: ambient at 30–40 % of total flux in 2,700–3,000 K, task at 300 lux on the pillow, accent at three times ambient on the surface, and a 1–3 % floor-level night path.
·Filament bulbs live or die on dimming compatibility: 2,200–2,700 K at CRI 90 with a trailing-edge dimmer, and a supplier who cannot name the driver will flicker at low output.
·Track lighting choice is a beam question: GU10 cylinders at 350–600 lm in 24°/36° for retail, integrated COB at 600–2,500 lm for lobbies where lamp changes are unacceptable.
·Fix the parameters before requesting samples — CCT, CRI, beam angle and dimming protocol — or the sample round measures the wrong thing.
Filament bulbs: form factor, dimming and the honesty problem
The filament bulb is the most aesthetically driven product in the LED catalogue, and the one most often bought on appearance alone. Three parameters determine whether it performs.
Form factor and lumen output. The shape dictates the application: ST64 and G95 for pendants and open fixtures, G80 for vanity, A60 for general retrofits, C35 and T30 for chandeliers.
Shape | Typical power | Output | CCT | CRI | Best use |
ST64 (straight) | 4–8 W | 400–800 lm | 2200–2700 K | 90 | Pendant, bar, restaurant |
ST64 (spiral) | 4–6 W | 350–600 lm | 2200–2700 K | 90 | Decorative pendant |
G95 / G125 globe | 6–10 W | 600–1,000 lm | 2400–3000 K | 90 | Vanity, lobby |
A60 / A19 | 4–8 W | 470–800 lm | 2700–4000 K | 80–90 | General retrofit |
C35 / T30 candle | 2–4 W | 200–400 lm | 2200–2700 K | 90 | Chandelier |
Dimming compatibility. This is where filament bulbs fail projects. Filament LEDs present a non-linear load to a leading-edge dimmer, causing flicker, dead travel at the bottom of the range, or buzzing. The fix is a bulb with a dimming range stated down to 5–10 % and a driver designed for trailing-edge dimmers — plus a dimmer rated for LED loads. If the dimmer and the bulb are specified independently, expect problems.
Colour consistency. Warm 2,200 K filament bulbs are typically binned at 3–5 steps. In a chandelier with 12 bulbs, mixed bins read as visible patches of pink and green. Specify a single bin and a single production batch.
Track lights: GU10 versus integrated COB
Track lighting is specified for its flexibility, and the choice between lamp-based and integrated heads determines the project's maintenance model.
GU10 lamp-based heads allow lamp replacement and future upgrades, at lower output per head (typically 350–600 lm). Best for retail where beam angles change with merchandising, and for projects with a maintenance contract.
Integrated COB heads deliver 800–3,000 lm with a purpose-designed optic, better colour consistency and a longer life — but a failed unit is a fixture replacement. Best for hotels, galleries and high-ceiling spaces where access is difficult.
Optical quality. Look for a lens, not a reflector-and-frosted-glass assembly. A TIR lens produces a clean 15°, 24° or 36° beam with a sharp cut-off; a reflector gives a soft edge and 25 % less usable intensity.
Colour and dimming. CRI 90 is the standard for hospitality, with a 2-step or 3-step MacAdam bin. Dimming to 1 % is often required in restaurants for the "candlelight" scene — verify the driver's minimum, not the dimmer's.
Track head | Output | Beam options | CRI | Dimming | Application |
GU10 cylinder | 350–600 lm | 24°/36° | 90 | Trailing edge | Retail, gallery |
Integrated mini | 600–1,200 lm | 15°/24°/36° | 90 | DALI / 0-10 V | Restaurant, bar |
Integrated standard | 1,200–2,500 lm | 15°/24°/40° | 90 | DALI-2 | Lobby, atrium |
Wall-wash head | 800–1,500 lm | Asymmetric | 90 | 0-10 V | Feature wall, art |
Track system details. 2-wire, 3-wire and 4-wire (three-circuit) systems are not interchangeable. Specify the adaptor type, the rated current per circuit (typically 16 A), and whether the track is surface, recessed or suspended. For 4-wire track, confirm the phase assignment on the drawing — mismatched phases are a common commissioning fault.
Ceiling luminaires: the quiet workhorses
Ceiling fixtures in hospitality are often selected for how little attention they draw. The specification still matters:
CCT selectability. A 5CCT switchable fixture (2700/3000/3500/4000/5000 K) reduces SKU count for distributors and lets a hotel tune per area. The trade-off is a slight efficacy loss and a switch that can be set incorrectly — mark the setting on the fixture label.
Diffuser and glare. Opal PMMA for even light, micro-prismatic for higher output without glare. In a hotel corridor, UGR below 22 is comfortable; in a guest room, avoid any fixture within the occupant's direct sightline from the bed.
IP rating by zone. IP44 minimum in bathrooms (zone 2), IP65 in zone 1 and shower areas. Many "bathroom ceiling lights" on the market are IP20 and should not be installed above a shower.
Emergency and sensor options. Corridor ceiling lights increasingly integrate microwave sensors with standby dimming to 20 % — a simple, code-friendly way to cut corridor energy by half.
Ceiling type | Output | CCT | CRI | IP | Application |
Slim surface downlight | 1,200–2,400 lm | 3000–4000 K | 80 | IP44 | Corridor, bathroom |
5CCT bulkhead | 800–1,800 lm | 2700–5000 K | 80 | IP65 | Utility, outdoor soffit |
Magnetic track spot | 600–1,200 lm | 3000 K | 90 | IP20 | Feature ceiling |
Linear ceiling cove | per metre | 2700–3000 K | 90 | IP20 | Indirect ambience |
Layering: how a hotel room is actually lit
A guest room typically uses four layers, and the ratios matter more than the products:
·Ambient — ceiling or cove at 30–40 % of total flux, 2,700–3,000 K.
·Task — bedside reading at 300 lux on the pillow, narrow beam, physically switchable.
·Accent — track or wall washer on artwork and texture, 3× the ambient illuminance on the surface.
·Night — a 1–3 % floor-level path light, often the detail guests remember.
Specify all four layers from one CCT bin family. A room with a 2,700 K filament pendant, a 3,000 K downlight and a 4,000 K LED strip reads as "renovated on a budget" — which is the opposite of the intent.
Building a supplier shortlist
Ask any hospitality lighting supplier for: a single-bin commitment per order, dimming compatibility tested with a named dimmer brand, LM-79 data for the decorative finishes, and a spare-parts policy for integrated fixtures. These four items separate a project supplier from a trading company.
LFL Lighting produces filament bulbs, track systems and ceiling luminaires for hotel, restaurant and retail projects, with bin-selected LEDs, tested dimming compatibility and OEM packaging for distributors. Send your mood board or a reference project — we will return a matched CCT and CRI proposal with samples.
Contact: shally@longingforlight.com | Request sample set and dimming compatibility list
Frequently asked questions
What colour temperature should a hotel guest room use?
2,700–3,000 K for ambient and 2,200–2,700 K for decorative filament sources, at CRI 90. Anything above 3,000 K in a guest room reads as clinical rather than restful.
Are LED filament bulbs dimmable?
Only when the bulb and the dimmer are matched. Filament sources need a trailing-edge dimmer, and the driver must be rated for the low load of a 4–8 W lamp — most flicker complaints at low output come from a dimmer with a minimum load above the lamp's draw.
How many layers of light does a hotel room need?
Four: ambient from ceiling or cove, task at the bedside and desk, accent on artwork and texture, and a night layer at 1–3 % for the floor path. Projects that skip the fourth layer feel either flat or harsh.
Related reading: Architectural & Decorative LED Luminaire Engineering · Comprehensive Commercial Indoor Lighting Analysis · Energy-Efficient Office & Workstation Lighting Standards.